{"product_id":"biqu-panda-bamboo-feeder","title":"BIQU Panda Bamboo Feeder - Smart Filament Buffer \u0026 Auto Refill","description":"\u003cp\u003eThe \u003cstrong\u003eBIQU Panda Bamboo Feeder\u003c\/strong\u003e is a motorised smart filament buffer that actively pushes filament to your printer, so the extruder is not left dragging it off a heavy spool or through a long PTFE run. Add a second filament source and it becomes an \u003cstrong\u003eauto refill\u003c\/strong\u003e system: when one spool runs out, it detects the break and switches to the next, so long prints keep going.\u003c\/p\u003e\n\n\u003ch2\u003eWhat It Solves\u003c\/h2\u003e\n\u003cul\u003e\n  \u003cli\u003e\n\u003cstrong\u003eLong PTFE paths.\u003c\/strong\u003e Spools in a drybox, on a shelf or across the room, where the extruder struggles to pull filament the whole way\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003eHeavy and bulk spools.\u003c\/strong\u003e 2kg, 3kg and larger spools that put extra drag on the extruder\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003eLeftover spools.\u003c\/strong\u003e Run the last few metres of one spool straight into a fresh one instead of throwing the end away or babysitting the swap\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003eOvernight and long prints.\u003c\/strong\u003e Auto refill picks up the next spool on runout, so a print does not stop because one spool came up short\u003c\/li\u003e\n\u003c\/ul\u003e\n\n\u003ch2\u003eHow It Works\u003c\/h2\u003e\n\u003cp\u003eEach feeder has its own drive and runout detection, controlled by an ESP32-S3 with a 1.3 inch OLED status display. Load and Retract buttons on the unit give you one-press filament changes, and a Wi-Fi web interface, opened from any browser on your local network, handles pairing, feed pressure, calibration and firmware updates over the air.\u003c\/p\u003e\n\u003cp\u003eStart with the Starter Pack, then add Expansion Packs as you need them. Up to three feeders can be combined for up to four filament sources.\u003c\/p\u003e\n\n\u003ch2\u003eChoose Your Pack\u003c\/h2\u003e\n\u003cul\u003e\n  \u003cli\u003e\n\u003cstrong\u003eStarter Pack.\u003c\/strong\u003e The feeder and filament hub, plus accessories to set up auto refill. The place to start\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003eExpansion Pack.\u003c\/strong\u003e One additional feeder with PTFE tube, double-sided tape, hex key, sticker and screws, for adding more filament sources to an existing setup\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003ePSU.\u003c\/strong\u003e 24V 2.8A power adapter with interchangeable plug heads and an inline switch\u003c\/li\u003e\n\u003c\/ul\u003e\n\n\u003ch2\u003eBeing Upfront\u003c\/h2\u003e\n\u003cul\u003e\n  \u003cli\u003eThis is \u003cstrong\u003enot an AMS replacement\u003c\/strong\u003e and does not do automatic colour changes. It feeds and refills one filament path\u003c\/li\u003e\n  \u003cli\u003eIf you also run an AMS, turn the feeder off when printing from the AMS so the two do not fight each other\u003c\/li\u003e\n  \u003cli\u003eTPU can work, but results depend on the filament path. Keep it short with as few bends as possible\u003c\/li\u003e\n\u003c\/ul\u003e\n\n\u003ch2\u003eCompatibility\u003c\/h2\u003e\n\u003cp\u003eOptimised for Bambu Lab \u003cstrong\u003eX1, P1, P2 and A1 series\u003c\/strong\u003e printers, including the X1C, X1E, P1P, P1S, P2S, A1 and A1 mini, and usable with most FDM 3D printers.\u003c\/p\u003e\n\n\u003ch2\u003eSpecifications\u003c\/h2\u003e\n\u003cul\u003e\n  \u003cli\u003e\n\u003cstrong\u003eType:\u003c\/strong\u003e smart filament buffer and auto refill feeder\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003eController:\u003c\/strong\u003e ESP32-S3\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003eDisplay:\u003c\/strong\u003e 1.3 inch OLED, 128 x 64\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003eControls:\u003c\/strong\u003e Load and Retract buttons, Wi-Fi web UI, OTA firmware updates\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003ePower input:\u003c\/strong\u003e 24V DC\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003eDimensions:\u003c\/strong\u003e approx. 96 x 52 x 42mm per feeder\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003eExpandability:\u003c\/strong\u003e up to three feeders, up to four filament sources\u003c\/li\u003e\n\u003c\/ul\u003e\n\n\u003cp\u003eBrowse the rest of our \u003ca href=\"\/collections\/printer-parts-upgrades\"\u003eparts and upgrades\u003c\/a\u003e. Ships fast from our Sydney warehouse with Australia-wide delivery.\u003c\/p\u003e","brand":"Biqu","offers":[{"title":"Starter Pack","offer_id":67732338540798,"sku":"PBF Starter Pack","price":124.99,"currency_code":"AUD","in_stock":true},{"title":"Expansion Pack","offer_id":67732348502270,"sku":"PBF Expansion Pack","price":119.99,"currency_code":"AUD","in_stock":true},{"title":"PSU","offer_id":67732348535038,"sku":"PBF PSU","price":37.99,"currency_code":"AUD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0688\/2338\/4318\/files\/BambooFeeder.jpg?v=1791973781","url":"https:\/\/www.filamenthub.com.au\/products\/biqu-panda-bamboo-feeder","provider":"FilamentHub","version":"1.0","type":"link"}